BIGIRON.com Timed Online Internet Only
2-Party Well Drilling Equipment AUCTION

Tuesday, May 12, 2009,
first item closes at 10:00 AM CST

Log on to www.bigiron.com to register and bid today!

For Item Location and contact information visit www.bigiron.com

Following items Owned by:
MEADOW GROVE FEDERAL CREDIT UNION

VEHCILES & TRAILERS:
1980 GMC Custom Deluxe 30 Well Drilling Rig, 12 ft. Flatbed, 350 V8 Gas Engine, Automatic Transmission, Briggs Vanguard 16 hp Grout Pump, Briggs Vanguard 20 hp Hydraulic Pump, LT225/75R16 Rear Tires, 7.50-16LT Front Tires, 58,717 Miles on Tack

1973 Chevrolet C60 Single Axle Pipe Pulling Rig, V8 Gas Engine, 4 Speed Transmission, 10 ft. Service Body, Shop Built 20 ft. Boom, 8.25-20 Tires, 110,325 Miles on Tack, VIN: CCE613V171646

1972 Ford F-600 Single Axle Flatbed Truck, V8 Gas Engine, 4 Speed Transmission, 1,000 Gallon Poly Water Tank, 8.25-20 Tires

1974 Ford F-600 Single Axle Flatbed Truck, V8 Gas Engine, 4 Speed Transmission, 12 ft. Flatbed w/ Tool Boxes, 100 Gallon L Shaped Fuel Tank w/ 12 Volt Electric Pump, 8.25-20 Tires

1974 Ford F-600 Single Axle Cargo Van U Haul Truck, 20 ft. Van Box, V8 Gas Engine, 4 Speed Transmission, 9R22.5 Tires

Ditch Witch T14A 16 ft. Tandem Axle Tilt Bed Trencher Trailer, Pintle Hitch, Fold Up Ramps, Lights, 7.50-16 Tires

Ditch Witch 10 ft. Tandem Axle Tilt Bed Skid Loader Trailer, 2” Ball Hitch, Folding Ramps, 6 ft. Tongue, 7.50-15 Tires

Shop Built 20 ft. Tandem Axle Flatbed Trailer, 8 ft. Wide, Wood Deck, 2” Bumper Hitch, 7.50-17 Tires  **NO TITLE**

Shop Built 12 ft. Tandem Axle Trailer, Setup for Mud Mixer, Hose Reel, 8 ft. Wide, 185/75R14 Tires  **NO TITLE**

TRENCHER:
Ditch Witch 4010DD Trencher Backhoe, Deutz 3 Cylinder Diesel Engine, 3,765 Hours, 31x15.5-15 Tires, 5 ft. Trencher w/ A450 Vibrating Knife, Front Blade, Backhoe, SN: 409739

SKID LOADER:
Bobcat 7753 Skid Loader, Diesel Engine, 2,537 Hours, 10-16.5 Tires, 72” Bucket, SN: 509630620

PUMPS:
Onan 16 hp Centrifugal Pump

Briggs 5 hp Centrifugal Pump

(2) Briggs 3 hp Centrifugal Pumps

MISCELLANEOUS:
WT 48” Pallet Forks for Skid Loader

Front Chain For Trencher

300 Gallon Fuel Barrel on Stand, 115 Volt Electric Pump

Antique Gas Buy Model 390 Fuel Pump, SN: 315312

Coleman 8 hp Generator

Power Washer w/ 5.5 hp Honda Gas Motor

270 Amp Mig Welder w/ Bottle

Oxygen / Acetylene Torch Set w/ Extra Bottles

Air Compressor, 3 hp 120 Volt Electric Motor

½” Military Air Hose Reel

(2) Ditch Witch Line Locator

Post Drill

Post Vice

Kohlswa Sweden Anvil

(4) 8 ft. x 5 ft. High Shelving Units

15 Ton Pintle Hitch Receiver

Roll of Cable

Steel Pipe

PVC Pipe

Steel & PVC Fittings

Lap Top Computer in Case

Printer w/ Ink Cartridges

Canon Fax Machine / Phone – 2 Years Old

Following items Owned by:
Francis L/ & Claudeen Penry - Elkhorn Valley Drilling, Inc
402-925-5364

VEHICLES & TRAILERS:
1965 Ford F600 Well Rig, 4 Speed Manual, V6 300 Gas Engine, Complete with Drill Stem, 140 ft. on Truck w/12 Stems at 150 Extra, Extra 6” Bits, Rotary Bit, Extra Turn Table, Pump Caps, Built for 150 ft. Rotary

1967 Ford F350 Dually Flat Bed Truck, 4 Speed Manual Transmission, V6 300 Gas Engine, Wood 11 1/2 x 7 ft. 9” Flatbed w/Side Boards

1976 International Pump Setting Truck, 4-2 Speed Transmission, 8:25-20 Tires,  32 ft. Boom w/8 ft. Extension, Rear Down Riggers, PTO Driven Pump, Hydraulic Break Away

Shop Built 20 Ft. Tandem Axle Trailer, 4 1/2 ft. Beaver Tail, Fold Down & Slide out Ramps, 8 ft. Wide, Trailer House Axles, (2) Spare Tires, Pinal Hitch, 8-14.5LT Tires

1977 Ford F250 Pickup, 4x4, 4 Speed Manual Transmission, 350 Gas Engine, Aluminum Topper, VIN:  F26HL033080

1967 GMC 7500 Truck, 4604 Hrs., 5-4 Double Shifter Transmission, V6 401 Gas Engine, 9:00-20 Tires, Twin Screw, 2000 Gallon Square Water Tank, Gravel Storage bin, Chicago Electric 115/230 Single Phase Generator w/8 Hp Briggs Engine, 1 Hp. 20 GPM Test Pump

TRENCHER:
Ditch Witch V30 Ditcher, 4 Speed Manual Transmission, 4 Cylinder Wisconsin Gas Engine, 27x850-19 Tires, Makes 5 ft. Trench, Front Blade, SN:  24807

PUMPS:
Teel 2" Transfer Pump w/14 ft. of 2" Hose, Gas Engine w/Strainer

2 Stage 10 Hp. Pump, 360 Gallon Open Discharge or 90 Gallon at 50 PSI & 4 Stage Pump, 380 Gallon Open Discharge or 360 Gallon at 40 PSI

1/2 Hp. 25 GPM Submersible Pump

1 1/2 Hp. 2 Wire 20 GPM Pump

Goulds 1/2 Hp. 115 Volt 10 GPM Pump w/Control Box

Berkley 1/2 Hp. 115 Volt 12 GPM Pump w/Control Box

Red Jacket 1/2 Hp. 230 Volt 10 GPM Pump w/Control Box

1/2 Hp. 230 volt 10 GPM Pump w/Control Box

1/2 Hp. 230 volt 10 GPM Pump w/Control Box

3/4 Hp. 230 Volt 20 GPM Pump w/Control Box

Red Jacket 1 Hp. 20 GPM 230 Volt w/Control Box

1 Hp. 15 GPM 230 Volt Pump w/Control Box

1 1/2 Hp. 15 GPM 230 Volt Pump w/Control Box

1 1/2 Hp. 25 GPM 230 Volt Pump w/Control Box

2 Hp. 50 GPM Single Phase 230 Volt 6FC Pump Head w/Control Box

5 Hp. 230 Single Phase 13FC 50 GPM Pump Head w/Control Box

Red Jacket 3/4 Hp. 12BC Pump Head Kits & (1) 5 Hp. 13FC 50 GPM Pump Head Kit

(Unused) Franklin 2 Hp. Motor w/Goules 33GS 20 Pump End w/2 Hp. Control Box

(Unused) Franklin 2 Hp. Motor w/ 33GS 20 Pump End w/2 Hp. Control Box

Franklin 5 Hp. 230 Volt 3 Phase Motor

Franklin 1/2 Hp. 230 Volt Pump Motor

Franklin 1/2 Hp. 230 Volt Pump Motor

Franklin 1/2 Hp. 230 Volt Pump Motor

Franklin 3/4 Hp. 230 volt 2 Wire Pump Motor

Franklin 1 Hp. 230 Volt Pump Motor

Franklin 2 Hp. 230 Volt Pump Motor

Franklin 2 Hp. 230 Volt Pump Motor

Goulds 1/2 Hp. 10 GPM Pump End

Roberts 1 1/2 Hp. 12 GPM Pump End

Red Jacket 2 Hp. 80 GPM Pump End

Demster 2 Hp. 20 GPM Pump End

Berkley 1 Hp. 15 GPM Pump End

Goulds 5 Hp. 60  GPM Pump End

Goulds 5 Hp. 60  GPM Pump End

Red Jacket Pump End

15 Hp. 150 GPM Pump End

Goulds 15 hp 150 GPM Pump End

Goulds 20 Hp. 200 GPM Pump End

MISCELLANEOUS:
Shop Made Casing Groover w/Extra Blades

1985 Ford F350 Pickup Box w/End gate (Red)

9 ft. F10 Snow Bucket w/F11 Quick Tach Mounts

Cement Mixer on Cart w/5 Hp. Briggs & Stratton Motor

Airmotor Model 602 Windmill Head Complete/Less Wheel Sections

Roll of Fine Braided Cable (Some Welds)

ZN40 Zinc Pipe Thread Compound (New Bucket)

Layne Boller 8" Head Tool & Packing Nut Tool

(2) Column Pipe Puller's 4" & 5" Threader

115-230 volt Generator, Single Phase

Dual Wench w/1/4 Cable, Direct Wind of Reduced Rotation Wind

Box of Rope:  95 ft. 3/4", 50 ft. 1/2", 80 ft. 1/2"

(4) Jack Stands

6" Continuous Belt

(2) 1/14" Sand Points

4" PVC End Caps (1 Complete Box Plus (16) in an Additional Box)

(2) Locking Observation Covers

(3) Monitor at the Well Pitless Pressure Switches

4" Sand Bucket

(2) Laval 3/4" & 2" Sand Separators

New Automotive Parts:  Tire Rod Ends, Coupler, Shifter Boots

Acetylene & Oxygen Torch Hoses w/Gauges (no tips)

Unused Baron No. 202 Pressure Tank

(5) Irrigation Top Shafts: (2) 1 1/2 x 1 1/4 x 36" Long, (1) 1 1/2 x 1 1/4 x 52" Long, (1) 1" Straight

28" Long, (1) Stainless Steel 1 15/16 x 1 1/2 x 45" Long

(2) Rigid Aluminum 24" Pipe Wrenches

(2) Irrigation Oil Tube Wrenches:  (1) 2", (1) 2 1/2"; Irrigation Shaft Holding Wrench

(2) Superior 48" Chain Pipe Wrenches

(2) Kegs (approx. 100 lbs.) of 1/2 x 3" & 1/2 x 2 1/2" Bolts

Several Irrigation Chains, Head Pulling Chains, Spider Chains:  (1) Sival Hook, (1) Choker Chain

Alkota 2122 110 Volt Hot Water Pressure Washer w/Hose & Wand, Extra Tips

(2) Gear Head Lift Chains

Pump Setting Tool w/Holding Brackets, Well Setting Flanges, Threaded or Flange

(2) Shop Made Gate Valve Tools

(5)  Chain Binders

(3) Log Chains

(2) Franklin 1 Hp. Panel Boxes for Submersible Wells, (1) 1/3 Hp. 230 Volt Submersible Pump Box, (1) 2 Hp. 230 Volt Submersible Pump Box

(3) Copper coated Ground Rods

Pipe of Schedule 40 Conduit: 200 ft of 1/2", 90 ft. of 3/4", 35 ft. of 1", 65 ft. of 1 1/4", 25 ft. of 2" Conduit

(2) Hydrants:  Unused 3 ft. Baker, Used 5 ft. Baker

Thread Cutting tool w/1" thread, 2' Dies

Red Thread Cutting Tool w/Extra Die

Mark 4" Pipe Cutter

Thread Cutting Tool w2 1/2", 3" & 4" Cutting Dies w/Handle

(2) Pitless Well Setting Tools:  5" & 6"

(3) Log Chains

1 1/4" Reemer

1 1/4" Reemer

1 1/2" Reemer

1 1/2" Reemer

Set of Bearing Checking Tools (no 60 Gauges)

Left Hand Taps for 1 1/4" & 1 1/2" Pump Couplings

3/4" 10 Thread Die (4) 1 1/2" 12 Thread Dies

(2) 1 1/4" Left Hand 12 Thread Dies (2) 1 1/2" Left Hand 12 Thread Dies

1 1/2" x 1 1/4" Left Hand Reducing Coupler; (3) 1 14" Left Hand Straight Couplings; (4) 1 1/2" Left Hand Couplings

(11) 2" x 1 1/4" Right Hand Thread Line Shaft Bearings

(6) 2' x 1 1/4" Left Hand Thread Bearings

(4) 2 1/2" x 1 1/2" Left Hand Bearings

(9) 2" Spider Insert Rubber Adaptors; (10) 2 1/2" Spider Insert Rubber Adaptors

Fitceburge Machine Works Metal Working Lathe w/9 ft. Bed, 110 Volt Motor w/Belt Drive, Complete w/(4) Chucks & Adjustable Drive Gears

Hummer Windmill Weights w/Rooster

Round Small Windmill Weight, Stamped (X30)

Windmill Vein Stamped (Homesteader Mill)  **NOTE:  Horse has 1 Broken Front Leg

REMOTE CONTROLED AIRPLANES:
P51 Mustang Radio Controlled Airplane w/OS 20 Engine, No Radio Equipment

GO/Chipmunk Radio Controlled Airplane w/ OS 60 Engine w/Fatuba 4 Channel Radio Equipment

Scratch Built Radio Controlled Airplane w/OS 15 Engine, No Radio Equipment

FT Stenson Radio Controlled Air Plane w/ OS 6P 40 Engine w/Old Style Radio Equipment

Scratch Built Radio Controlled Airplane w/40 cc Magnum Engine & Airtronics Radio Equipment

Scratch Built Radio Controlled Airplane, KB40 Engine, Channel 16 Airtronics Radio Equipment

J3 Piper Cub Radio Controlled Airplane w/OS40 Engine, No Radio Equipment

Scratch Built Radio Controlled Airplane w/OS 20 Engine & Old Style Airtronics Radio Equipment

GL Birdy 40 Radio Controlled Airplane w/OS 40 Engine, No Radio Equipment

Scratch Built Radio Controlled Airplane w/OS 40 Engine, No Radio Equipment

Scratch Built Radio Controlled Airplane w/Barn Door Alienons, No Engine, No Radio Equipment

Scratch Built Radio Controlled Airplane w/OS 60 Engine, No Radio Equipment

Bi-Plane Radio Controlled Airplane w/15 cc Engine, Channel 16 Radio Equipment

Glider Radio Controlled Airplane w/O49 Engine

Scratch Built Radio Controlled Airplane, Only Fuselage & Wings

For Complete terms visit www.bigiron.com